| Item | Content |
|---|
| Product No. | RUPA Claw-RC1 | | Version | V1.0 | | Release Date | 2026-03-19 | | Effective Date | 2026-03-19 | | Document Status | Under Revision | | Prepared by | Wang Zhihai | | Reviewed by | — | | Confidentiality Level | Public |
| Version | Release Date | Update Record |
|---|
| V1.0 | 2026-03-19 | Initial release |
|
|
|
|
|
|
1. Product Introduction
Built on Rockchip flagship RK3588, this device runs Armbian Ubuntu 26.02 and is deeply optimized for OpenClaw AI agents. It supports one-click installation and rapid deployment.
The streamlined Armbian system ensures long-term stable operation, suitable for both development and production scenarios.
2. Specifications
Product Specifications
| Item | Description |
|---|
| CPU | RK3588 Octa-core (Cortex-A76 + Cortex-A55), up to 2.4GHz | | GPU | Mali-G610; supports OpenGL ES 1.1/2.0/3.2, OpenCL 2.2, Vulkan 1.2. Built-in high-performance 2D acceleration hardware | | DDR | LPDDR4X, optional: 4GB / 8GB / 16GB | | NPU | 6.0 TOPS | | OS | Armbian Ubuntu 26.0.2 | | Onboard Storage | Supports eMMC 5.1 & SDIO 3.0, optional: 32GB / 64GB / 128GB | | Display Output | 2 × HDMI 2.1, max 4K@60Hz, HDCP 2.3
1 × 4-Lane Type-C (DP 1.4a), max 4K@60Hz, HDCP 2.3 | | Ethernet | 1 × Gigabit Ethernet | | Wi-Fi | Wi-Fi 6 MIMO, IEEE 802.11a/b/g/n/ac/ax | | RTC | RTC supported, compatible with CR1220 battery | | USB | 1 × USB3.1 HOST Type-A (5Gbps)
1 × USB3.1 OTG Type-C (5Gbps)
2 × USB2.0 HOST Type-A (480Mbps) | | Reserved Interfaces | 2 × UART TTL (3.3V level)
6 × GPIO (3.3V level)
1 × DP
1 × SATA | | Power Supply | 12V 2A DC, 5.5×2.0mm barrel connector | | Cooling | Passive cooling | | Power Consumption | 10W (without external peripherals) | | Net Weight | 251g ± 10g | | Package Weight | 610g ± 10g | | Operating Temperature | -20℃ ~ 45℃ | | Storage Temperature | -20℃ ~ 70℃ | | Operating Humidity | 20% - 85% RH (Non-condensing) | | Storage Humidity | 5% - 90% RH (Non-condensing) |
3. Product Schematic Diagram Image Added
 Image Added
Firmware Link: Flashing Tool & Driver Link: https://pan.baidu.com/s/1ugVAJ35VeWkUoKOjiLgvXQ?pwd=3iyb
Password: 3iyb I. Preparation- RUPAClaw-RC1 host
- USB 2.0 A to C cable
- Tweezers
- 12V power adapter
- Windows computer
Connect the computer to the Type‑C port of the RUPAClaw‑RC1 host using a USB cable. Short the two solder points of the MASKROM button with tweezers, then power on with the 12V adapter to put the device into MASKROM mode.- If the eMMC is blank, the MASKROM button is not required.
- For devices that have been flashed with Armbian, you must short the MASKROM button to reflash the firmware.
 Image Removed
 Image Removed
II. Flashing Procedure- Launch Rockchip Development Tool. Version V2.84 or higher is required.
- Load the Loader and system files, then check the corresponding boxes.
Loader address: 0xcccccccc
System address: 0x00000000 - Put the device into MASKROM mode. If it is in Loader mode, switch to MASKROM mode via Advanced settings.
- Click Execute to start downloading. The process takes approximately 5 minutes.
 Image Removed
| 